Blog

The Makita TM30DZ show could be a cordless multi-device powered by Li-ion 10.8V CXT slide battery. Makita’s 10.8V tools CXT range features a slide battery. The TM30D‘s ergonomically designed barrel grip and ideal diameter size make it lightweight and easy to handle. The slide battery fits easily into the equipment and new chargers and is fitted with the same high level of structural strength and built-in protection to avoid overload or overload.

• Large on/off slide switch with lock-on button for operator convenience.
• Includes adapters to fit most competitive accessories.
• Small diameter barrel grip (only 2-3/8″) for easy handling.
• Ideal for wood flooring, tile, plaster, sheetrock, wood, PVC and a variety of other applications.
• Equipped with Star Protection Computer Controls™ to protect against overloading, over-discharging, and over-heating.

If the motor doesn’t work:

• Begin by testing the power switch and its installation to ensure that no damage is caused as damage to heat and water can be the culprits of a device that will not begin.
• Accumulation of dust and dirt inside a tool and can prevent a tool from working so that brushes and springs are where you should look next. Brush channels-enclosures composed of brushes and springs located at the end of an engine where electricity is redirected-can be worn over time and shortened.

Sparks or smoke while using the system:

Disconnecting or wearing down the carbon brushes is the most likely cause of sparks and/or smoke. They can create sparks and/or smoke when rusty or damaged carbon brushes communicate abnormally with the communicator. The carbon brushes are two parts of an electric motor that transmits current via the commutator to the rotating armature.

Unusual noise while in use:

When grinding a surface or after doing a hard job, add less pressure to the Multi-tool. To allow the device to cool down, it is suggested that the multi-tool spin freely for a few seconds. Give the multi-tool some time after any job to cool down, and refrain from continued use over long periods.

The heat emanating from the device’s body:

Needs cleaning: The grease can contain gravel, sand, or metal bits which would cause friction and thus cause heat. Cleaning the inside of the unit will resolve this.

Must have more grease: A lack of grease in the wheel bearing may cause an excessive amount of heat. Grease is a lubricant that helps reduce the amount of internal friction inside the tool.

Toptopdeal provides you with Makita’s best LXT Multi-Tool features a tool-less accessory clamp with a lever-style locking system to quickly and easily adjust accessories. It is an ergonomically designed barrel grip that is lightweight and easy to handle, with a large diameter size and shape that suits the hand to make handling extra comfortable.

The Makita DHP458Z combi drill is part of new slide platform versions of the 10.8v CXT (Compact eXtreme Technology). The combi-drills offer the kind of features and advantages you’d expect to find in a drill that can punch 13 mm holes into masonry while retaining a lightweight, ergonomic footprint. It has considerably more power, more drilling capability, increased robustness and additional extras such as a depth stop and side handle.

With 21 torque levels for screw driving loads and a whopping 7,500 blows per minute in hammer mode, it’s a real combi-drill powerhouse.

• Compact design

If you’re forced to work in small or cramped spaces but don’t want to compromise on the strength and flexibility of the equipment you’re using, then it’s great to know Makita combi drill has a head length of just 225 mm.

• Torque setting

The Makita combi drill runs up to 2,000rpm in high mode, 500rpm in low mode, with a high impact output of 30,000ipm and low pressures of 7,500ipm, with a maximum torque of 54Nm with 21 settings and drill mode.

• Lightweight

Although the size is small, compact and lightweight, it still has 2 speeds, 20 torque settings and provides a hard torque of 35Nm. The engine is brushless and holds the weight to about 1 kg.

• Brushless Motor

With increased power, speed and overall increased tool life, the brushless motor provide up to 50 percent more runtime. The Combi drill can drill into wood (76 mm), Metal (13 mm) and Masonry (16 mm) with its metal gears and 45 Nm of Torque.

• It is a Great All-Rounder

You expect to be able to do lots of things with your combi-drill. So with the Makita Combi drill in your hand, thanks to the 30,000bpm, and a whopping 65 mm in wood, plus 16 mm in steel, you’ll be drilling up to 16 mm into concrete, bricks, and maçonnery in hammer mode.

Makita Screwdriver DFR550Z Such models feature a more durable casing attachment which makes it ideal for both professional use and DIY use. This 18v Makita DFR550Z LXT 18V cordless auto-feed screwdriver gun provides high operating performance from fast rotational speed and enhanced screw strip control. The Auto-Feed Screwdriver has a dustproof design for smooth-sliding action

The screw guide avoids screw strip tangling and can fold against the auto-feed housing for storage and transport. It has a collated screw scale with a high range of 25 mm to 55 mm. Equipped with an anti-tilt tool to avoid the screws swinging while being fastened.

• Anti-tilting system to avoid the swaying of screws.
• Adjustable stopper base with 7 different screw length settings – 4 x 25 – 55 m.
• Silent clutch – less noise at the end of the driving process.
• Rubber Cap securely fixed to Stopper Base for accurate positioning and slip prevention.
• Convenient carry hook for temporarily hooking the tool.

Overheating                                  

Used for Too Long: The screwdriver DFR550Z starts heating up when you use the drill for a long period of time. Just let the button run to interrupt drilling, and let the drill cool down. Make sure that the safety lock is in place for security purposes. You should restart drilling once it’s cooled down again.

Trigger Switch Do Not Work:

Engaged in a secure lock: To start the screwdriver you have to push down the button. If the safety lock is locked you cannot press the trigger. Before operating the device, ensure the safety lock is switched to forward or reverse.

The Trigger Committee went wrong: If the trigger switch is pushing down but not activating the motor, the trigger could be wrong.

Battery died: If the battery is dead or not properly attached the drill will not operate. Make sure the battery is charged and that the drill is attached.

Slipping Clutch Drill:

Slip-Clutch configuration is not acceptable: If the clutch slips before a screw are completely drilled in, this means that the torque value is not high enough. Simply rotate the setting to a higher value. You may want to change the setting to a lower value when you drill the screw too deeply.

The clutch has numerical values which reflect the amount of torque the drill can exert on a screw. You can set the value of the torque according to the type of screw.

Clutch Leaf Spring Worn Failed: If the clutch does not ‘ click ‘ securely on the right gear, the leaf spring may be worn out or simply lacking. Opening the drill is a common occurrence for somebody and they don’t put the leaf spring back in its proper place before reassembling.

Disconnected battery:

The LED light will not turn on when the battery is removed. Check with our battery replacement guide to make sure the battery is properly attached. Once the battery is properly attached, press the trigger to see whether the light is flashing while the drill spins.

Safe guide:

• Using Work Gloves: Power drills, especially on high torque, give off intense vibrations. Because of the effect and friction they can also reach high temperatures. To handle the device safely you must always wear thick gloves. This is also helpful when you adjust drill bits or loosen the chuck to avoid contact with the hot surface.
• Hold your job piece safe: You don’t want to move the piece of wood or metal that you’re working on while you drill. Clampdown or lock the workpiece into a vice before applying the power drill to it.
• Use the proper drill bit for every job: Ensure you are using the right drill bit, depending on the job and the content. Using the wrong bit will lead to a bad job and will require a lot of force to be used too. With time, it can damage the power drill too.
• Place the drill bit correctly: Make sure the drill bit is inserted into the chuck correctly and lock it tightly with the chuck key. Your power drill will not make straight holes with a loose bit, and it could slip.
• Apply appropriate pressure to the Drill: Most of the work should be performed by your power drill, so don’t use too much energy. When you push too hard, you can slip the power drill or you can strain the engine.

The Perfect Power Tool is Makita DRT50Z  Routers. It’s a brushless motor that provides extended battery running times and plenty of power. Makita DRT50Z 18v Cordless Brushless Router / Trimmer LXT for cord-free routing & trimming is a welcome addition to the 18v LXT range. A soft start and electric brake make this a precision device you can easily handle.

To create friction a Brushless motor can produce a higher torque measure per weight without brushes. The Makita DRT50 router/laminate trimmer comes with a trimmer base which is a round base for smooth and quick cutting with an extended opening.n, for excellent bit visibility.

• Connectable to extractor of powder.
• Twin LED job lights
• Push-button switch with lock-on/off.
• High durability and accuracy.

For a worker, the most important thing is to keep their equipment in excellent condition. The high-quality router can perform many tasks, such as shaping, cutting and trimming materials. This powerful tool can bring various benefits and uses to you.

Sometimes the non-performing or non-functional router may cause some irritation and trouble. There are some explanations why your equipment doesn’t work properly such as broken pieces, problems with belt or wood dust, or other issues.

Slips Bit:

When bit begins to fall in the middle of the process using a chuck. While the chucks are turning around and realizing the bit is over.

If this problem arises then turning off the machine and tightening up the chuck is important. If that doesn’t work out, check to see does its key has been stripped or not. It can be the reason for a loose chuck.

Overtightened nut:

You don’t have to twist a collet nut as much as you would tighten when installing a tool, like a table-saw. Alternatively, just twist the nut about an eighth of a turn after it snugs up.

Broken Bit:

This can affect your body or hurt your creature when the bit is broken. For example, if it reaches your eyes, it could cause a serious problem.

To prevent this problem the best thing to do is to buy a high-quality router bit. Look for the one of a famous brand for example. Make sure you have correctly configured it to avoid any additional issues.

If it doesn’t fit properly, the use cycle will stop or break in the middle of it. Often, the important thing is to test the sharpness of the bits before using it. Don’t forget to wear this protective gear when working with the wood tool.

Leaving bits too long in a router:

If you don’t use a bit and it’s been more than a couple of days in the collect, delete it from your router. Even inside a collet, moisture may cause rust, and that may seize a bit of shank inside the collet.

Safety Tips:

• Make sure you have selected the correct bit. Test the size, shank strength, length and diameter of the cut, and bit sharpness.
• Be particularly careful when handling tiny pieces. Make sure test cuts of a safe size in solid unchecked stock.
• Do not force-feed the router in any case or function.
• Do not run electric routers in hot, muddy, or acidic conditions.
• Keep in mind always that bits and blades are designed to cut through motion, so bear them in the right direction.
• Hold the router under control and keep it tight all the time. Hold both hands on handle or knobs.

Makita DJR360ZK 36V LXT Reciprocating Brushless Saw powered by two 18V Li-ion batteries. Makita‘s brushless motor delivers 0-3,000 strokes per minute combined with a stroke length of 20 mm for quicker and more efficient cutting. Also conveniently located with the electronic 2-speed controls, blade speed is controlled through the variable trigger on the soft-grip handle.

The switching button on the tool handle & Paddle switch on the tool body makes it easier to operate at any grip spot, allowing versatile use of any trigger. Twin switches are designed for the most comfortable grip, and the work area is lit by an LED light.

• Powered by two 18V series Li-ion batteries to supply power to the powerful 36V DC motor drive system.
• The compact and lightweight design.
• Ideal for working in tight spaces.
• Two switch levers with variable speed control.
• Easy, safe operation in any grip position, fully versatile reciprocating saws using either trigger.

Adjust Angles to Quick Cut:

When cutting through thick material, periodically change the angle of the blade. It reduces the surface area being cut, which reduces the friction and makes for a faster cut. And whenever possible, keep the shoe tight up against the cutting surface to avoid kickbacks and to keep the material from rattling around.

Avoid Waggle—Use Smaller Blades

Blades for reciprocating saws come in different lengths for a reason. Cutting smaller material with longer blades can cause the end of the blade to violently waggle back and forth. This can result in a slower cut, a whole lot of vibration and possibly a bent blade. So choose a blade only a couple of inches longer than whatever you’re cutting.

Extend Blade Life with Lubrication

Blades heat up as you cut, especially when you’re cutting metal, and a hot blade dulls quickly. If you have a lot of metal to slice, rub on blade lubricant between cuts. Blade lubricant helps keep the blades cooler and the teeth free of clogs from metal chips.

Cut Plastic with Dull Blades

In some cases a dull blade is preferable: Cutting plastic pipe with a sharp, aggressive blade can cause the teeth to grab the pipe and jerk it back and forth instead of cutting it. A dull wood blade cuts through plastic almost as well as a blade specifically designed for the task.

Safety tips:

• Make it a point to clear all the clutter from your work area before you start work.
• Longer blades are more versatile, so reciprocating saws aren’t fantastic at that. A shorter blade will give you a straighter cut and you’re not going to have to do wiggle or flex.
• Hold the handles clean of dirt and grease. Make sure the blades are fairly sharp for the job.
• When the reciprocating saw cleans or changes blades, turn off the power supply and unplug the saw. Never leave the tool unsupervised.
• Never use a reciprocating saw in an area where fuel materials are stored. Sparks emitted by the tool can cause a fire very quickly.
• Never reach around or beneath the material you cut. You can get yourself seriously injured. Always keep both hands on the saw when running.

The main reason for using an angled drill is to screw a screw or drill a hole in areas with limited space or access, where using a traditional power drill or a cordless drill/driver to do the job is simply not an option because you simply can not drill or screw in a straight line.

If you are looking for purchasing an angled drill you should also look for one that comes with at least two batteries and a charger.

Parts of a Drill and How To Use It

As we have established above, angled drills come in mains and battery powered form, the latter giving you more scope for accessing more limited work areas.

Key locking chuck

A special chuck key (this looks like a cog on the end of a handle) kits in to normally one of three holes at the end of the chuck and is used to turn a gear, also at the end of the chuck, that in turn closes the jaws of the chuck and clamps down on the item inserted into it.

Keyless chuck

Instead of having a key to tighten the jaws, you use your hand to turn the exterior of the chuck that in turn tightens or loosens the jaws.

most models of Angle drill allow you to get enough pressure by hand to hold any size drill or screwdriver bit and when working in a confined space, this is much easier than trying to tighten and untighten with a key.

Trigger Switch

Drills can look like a toy gun to play with, and the fact that the operating switch is located in the same place as a trigger helps support the look. The trigger switch is the on-and-off mechanism on a drill. Some models will have only one speed and one simple switch.

Drill Shaft and Drill Bits

The drill shaft is the pointed part of the drill that holds the motor and the chuck. It is also where the rotation clutch is located. Like most electrical motors, the drill operates with a clutch to control power. Drill bits are the fun part – these multiple pieces can be changed according to the project at hand. Different bits are needed for different materials and use.

Angle Drill is a wireless power tool. It’s something generally used by people in different trades where people need something like this. Makita Angle Drill is a Best cordless as well as a brushless power tool. Instead of trying to bend your neck and back through impossible angles, only use the most flexible of all the drilling tools when you need to drill in a hard-to-reach region. The Makita DDA460ZK twin brushless angle drill is designed to suit the needs of the plumbing and electrical trades. The automatic torque drive optimizes the torque and rpm ratio in any situation for optimum performance.

Advantages of angle drill:

A right angle drill is a tool with plenty of advantages and no real disadvantages:-

Tight Spaces

Right angle drill is designed to access spaces that conventional drill can’t reach, those tight areas behind beams or joists that you just can’t get to otherwise. This is the greatest advantage of the right angle drill, and the reason most people would buy one.

Torque

Most of the right angle drills have 3-speed motors. This offers a lot of torque when you need it, and also allows slow drilling when needed.

Extensions

Through extensions to the drill bit, a right angle drill may hit some very tight spots. While extensions can also be used through traditional drills, a right angle drill allows you to drill almost anywhere in the building.

Versatility

Some right-angle drills allow the removal of the drive head and for the chuck to be used as a conventional drill. That makes it an ideal, versatile replacement for your normal drill.

Comfort

The side handle on a right angle drill gives a great deal more control when using, and some also offer a grip and trigger that will twist, increasing the possibilities when using the right angle drill.

Given the need to access difficult places, the design of the handles makes using the drill much more comfortable.

1. Makita DHR400ZKU 36V LXT Brushless SDS-Max Rotary Hammer Drill Body Only In carrying Case

Makita DHR400ZKU is a cordless SDS-Max rotary hammer. The DHR400ZKU LXT Brushless and Cordless SDS-MAX Rotary Demolition Hammer has a 2-mode operation with rotational hammering and hammering only. The choice is a rotation with the Makita SDS Hammer Drill for rapid drilling into concrete, rotation only drilling for metal/wood or hammer only for chiseling. Whatever the material gives fast and efficient results.

       SPECIFICATION :              

• Voltage: 36v (2 x 18v)
• No Load Speed: 250 – 500 rpm
• Blows per Minute: 1,450 – 2,900 bpm
• Shank: SDS-MAX
• Max TCT Bit: 40 mm
• Max Core Bit: 105 mm
• Impact Energy: 8.0 J                 
• Net Weight: 7.3 – 8.1 kg

• Makita DHR281ZJ 36V Brushless SDS + Rotary Hammer Drill Body With Quick Change Chuck In Case

This Makita DHR281ZJ Twin 18v SDS+ Rotary Hammer has XPT – Xtreme Protect Technology which is optimum protection against dust and splashes water even under harsh conditions. It also comes with an SDS-PLUS quick-change chuck which enables you to use more variety of drill bits for your specific application.  

       SPECIFICATION :                                                                       

• Battery Compatibility: 18v Lithium-Ion LXT
• Voltage: 36v (18vx2)
• Impact Energy: 2.8 J
• Blows per Minute: 0-5,000 bpm
• No Load Speed: 0-980 rpm
• Drilling Capacity ø Max in Wood: 32 mm
• Drilling Capacity ø Max in Steel: 13 mm
• Drilling Capacity ø Max in Stone/Concrete: 28 mm
• With Drill Bit: 68 mm
• Weight: 4.90 kg

• Makita DHR264ZJ 36V SDS+ Rotary Hammer Drill Body Quick Change Chuck With Case

Makita is one of the leading manufacturers of professional power tools on the market. The DHR264ZJ is a 26 mm cordless combination hammer powered by two 18 V Lithium-ion batteries in series.  The Makita DHR264ZJ is a 26mm cordless SDS plus rotary hammer drill based on models BHR262T but powered with 2 x 18V batteries giving the equivalent power of a 36-volt machine.

       SPECIFICATION :                 

• Voltage: 36v (2x 18v)
• Battery capacity: Up to 5Ah
• Charge Time: 36 minutes for 4Ah, 22 minutes for 3Ah
• Max. in steel: 13mm
• Max. in wood: 32mm
• Max in concrete: 26mm
• No-load speed: 0-1,200 rpm
• Impacts per minute: 0-4,800bpm
• Impact energy: 3.0 Joules
• Chuck type: SDS+ plus (quick change)
• Operation modes: 3 modes
• Net weight: 4.7kg

SDS Sizes and Ratings

• SDS Plus is the smallest of the three. The shank is 10mm and inserts 40mm into the chuck. It is rated for hammers up to 4kg.
• SDS Top is a rare configuration. It uses a 14mm diameter fitting that inserts 70mm into the chuck. SDS Top is rated for hammers in the 2kg to 5kg range.
• SDS Max is a common industrial fitting. It uses an 18mm shank with three open grooves instead of the two rolling balls employed in SDS Plus and SDS Top. The shank inserts 90mm into the chuck. SDS Max is rated for hammers over 5kg.

We hope that ours is one of the most useful reviews of SDS hammer drills you read and that at least our buying tips will help you get the best purchase possible for your hard-earned dollars.  If you would like to purchase Best SDS hammer drills, please visit our Toptopdeal website.

Makita GN900SE is a cordless clipped head Nailer developed for framing applications. It runs on gas for powerful hose and cord-free nailing, as well as 7.2v lithium-ion batteries to power the onboard electronics. They are actually a pretty versatile tool. You can use them on trim. You can also use them to put furniture and cabinets together and attach door and window moldings and thick baseboards.

As for how far you can sing the nails, only about a 16th of an inch into pine, so keep that in mind when working with harder wood. The depth adjustment knob is large enough to make easy adjustments, but I still think that it still needs to be adjusted a bit to drive the nails further into the wood if needed.

Features and benefits

• Easy Handling by using fuel gas as the power source, not using hoses and compressors.
• Dual-position hooks are convenient for hanging from rafter or steel pipe.
• Aggressive spikes allow for a firm grip on the material when firing.
• The air filter protects the cylinder from dirt and debris to prevent malfunction.

User comfort

Considering the basic cost of a finish Nailer, we strongly suggest that you visit a local retailer and find a model that is comfortable in your hands. This is a tool that should deliver consistent results based on how you handle it. The quality of the work starts with your hands.

Safety

All cordless nailers share the same basic safety feature, they require the tip be pressed against what you’re trying to drive the nail into to operate. You can press the trigger all the live-long day and unless that tip is depressed fully, it won’t operate.

They all also come with a fan to clear away the spent butane. When you depress the trigger, you should hear the fan turn on.

Conclusion

The Makita GN900SE features Makita’s LED low battery and error detection system, and a shock-absorbing battery fitting to protect the terminals. It has a quick loading system that is easy to see. Its lack of comfortable grip turned us off.  Makita Nailers is the best power tool. In fact, they’re some of our best-selling tools here at Toptopdeal.

We hope you found value in our reviews of Makita finish nailers, and that they help inform you on the right choice. 

Makita Jigsaws is an Ultra-compact Machine that is Lightweight and has a Brushless Motor for Longer Battery Runtime and Less Maintenance. Its Rubberized Soft Grip Handle Provides Increased Comfort on the Job. Makita Jigsaws are primarily used to make curved, intricate cuts in wood, but can also cut through a number of other materials such as plastic, sheet metal, and ceramic tile.  

Makita DJV181Z 18v LXT Cordless Barrel Grip Brushless Jigsaw Body

Like the above reviewer states, the body grip on the DJV181 is a key benefit. It allows you amazing levels over control over your cuts, especially curves. Equally, flip the jigsaw upside down, and the barrel grip is ideal for making plunge cuts from the underside of the material.

Features:

• Brushless motor
• New improved dust extraction hose joint
• Rigid aluminum base bevels 0 to 45 degrees left and right
• Change lever for 3 orbital settings and straight cutting
• Tool-less blade change
• Variable speed control dial
• Soft start feature
• Twin LED job light

SPECIFICATION:

• Voltage: 18v
• Max. in steel: 10 mm
• Max. in wood: 135 mm
• Max in aluminum: 20 mm
• Strokes per Minute: 800 – 3,500 pm
• Shank: Universal
• Stroke Length: 26 mm
• Noise sound pressure: 78 dB(A)

Metal

You can also use a jigsaw on metal, which can be useful when making a hole in a piece of material through which a pipe can fit. There will also be times you’ll need to cut curves in metal for it to fit on a wall.

Ceramic Tile

There are a number of instances when you might need to use a jigsaw with ceramic tile. For example, you might need to cut a semicircle or curve around a pipe. With the correct blade on your jigsaw, you can easily accomplish this.

Carpet

Although most people wouldn’t immediately think of it, you can use a jigsaw to cut carpet. This offers a more accurate cut than you’d manage with a utility knife or by using scissors.

Reasons why you should buy Makita Jigsaw.

Makita jigsaw can be used to make both straight and curved cuts in a wide variety of materials, including wood, particleboard, plywood, plastic, metal, even ceramic tile.

Kid-Friendly

With the proper instruction and adult supervision, children of various ages can use a jigsaw safely. The tool rests on the surface of what it is cutting, so it doesn’t require a grown-up’s strength to hold it in place.

Easy to Use

jigsaws are easy and straightforward to use regardless of your experience level. Insert the blade, plug in the tool (or pop in the battery if it’s cordless), and you are ready to start cutting.